Skip to content
Intelli-Clean Solutions · Tampa, Florida

Commercial concrete polishing, taken to mirror.

Polished concrete, epoxy flooring, polished overlays and staining for warehouses, stores, restaurants, dealerships, clinics and offices in Tampa and across Florida. Drag the grinder over the raw floor and watch each pass turn it to glass.

Polish it yourselfWarehouse

ReadyDrag the grinder across the raw floor

Floor polished0percent
Warehouse floor shown0sq ft polished
Machine time, typical0.0hours
Building
Machine
  • Warehouses and plantshardened, dust-free floors that take forklifts
  • Retail and showroomsmirror gloss that reflects the whole room
  • Restaurants and hotelsseamless floors that clean up fast
  • Clinics and officesdust-controlled work, phased around you
Welcome to Intelli-Clean

A floor that earns its keep

We test the slab, match the finish to the traffic, grind and harden it with real diamond tooling and walk the finished floor with you, so the shine lasts for years and the upkeep stays small. Based in Tampa, working across Florida.

  • Slab first, finish secondWe test hardness, moisture, cracks and old coatings before any tool touches the floor, so the finish is built on facts.
  • Real diamond toolingMetal and resin diamonds work up through the grit steps in the right order, with no shortcuts that leave scratches.
  • Hardened from withinA densifier fills the pores, so the floor resists dust and wheel wear without a film that can peel.
  • Dust under controlShrouded machines and HEPA-grade extractors keep the air clean in stores, clinics and offices around the work.
  • Phased around youNights, weekends and zone-by-zone plans keep your doors open and your crew working.
  • Walked with youWe check the finished floor with you in good light, explain how to care for it and fix anything that needs a second pass.
Commercial first

A floor for every kind of building

Warehouses, stores, restaurants, dealerships, clinics, offices, hotels and plants each get a finish matched to their traffic. Slide sideways to see them.

The grit ladder

From a rough slab to a mirror in seven steps

Keep scrolling. The same showroom floor climbs from a coarse grind through densifying, honing and polishing to a glass finish, while a microscope shows the scratches getting finer and the gloss reading climbs.

Step 1 of 7

30 to 70 Coarse grind

Metal-bond diamonds cut the slab flat and strip glue, paint and old coatings. The surface is rough and dull, and that is exactly right.

Typical particle size about 400 micronsGloss about 6 GU

Concrete Grinding
Step 2 of 7

100 to 200 Refine

Transition diamonds remove the scratches left by the coarse step and start to even out the surface.

Typical particle size about 100 micronsGloss about 12 GU

Concrete Grinding
Step 3 of 7

Densify Harden the slab

A densifier soaks in and reacts inside the concrete, filling pores and hardening the surface from within. This is what makes a polished floor tough.

Typical particle size pores filledGloss about 16 GU

Concrete Densifiers and Hardeners
Step 4 of 7

400 to 800 Hone

Resin diamonds smooth the surface to a satin sheen. Reflections appear, soft and fuzzy at first.

Typical particle size about 25 micronsGloss about 34 GU

Concrete Polishing
Step 5 of 7

1500 Polish

A finer resin step brings up depth. Ceiling lights now show as clear shapes in the floor.

Typical particle size about 10 micronsGloss about 62 GU

Concrete Polishing
Step 6 of 7

3000 Mirror

The finest step gives a glass-like gloss. Fixtures, windows and people reflect with sharp edges.

Typical particle size about 5 micronsGloss about 88 GU

Retail and Showroom Floors
Step 7 of 7

Guard Protect and burnish

A stain guard is applied and burnished in with a high-speed machine. The sheen is locked in and the floor sheds spills.

Typical particle size sealed and burnishedGloss about 94 GU

Concrete Sealers and Stain Guards

Keep scrolling to climb the grit ladder

Services

Six diamond discs, every service

Pick a disc to open its group of services. Each one links to a page with the details.

Pick a disc to open its services

Group A

Polished Concrete Floors

Concrete polishing by property type: warehouses, retail, restaurants, dealerships, healthcare, offices, hotels and plants.

All polish services
Sheen Lab

How glossy do you want to go?

Slide from matte to mirror on a real room and watch the reflections sharpen. Then pick the sheen that fits your building.

Room
Semi-gloss
FinishHigh gloss
Gloss reading60 GU
ReflectionsClear
Typical useShowrooms

Gloss units are a typical reading at a sixty degree angle. Ranges are approximate: matte about 5 to 15, satin 15 to 35, semi-gloss 35 to 60, high gloss 60 to 80 and mirror above 80.

Before and after

The same floor, raw and then mirror

Four buildings, each shown before and then after. Drag across the picture to polish it.

Before: A huge warehouse aisle between pallet racking with a raw, dull, scratched and stained concrete floorAfter: The same warehouse aisle with a mirror-polished concrete floor reflecting the lights and racking
The WarehouseSee the service

Drag anywhere on the picture, or use the arrow keys. It is the same spot both times.

The work

Tools, dust control and a gloss meter

From the first grind to the final reading, every step is done with commercial equipment and checked.

  1. A ride-on planetary concrete grinder with a dust shroud cutting a huge empty warehouse floor1

    Grind

    A ride-on planetary grinder levels the slab and strips what is on it, the foundation of every polish.

  2. An edge grinder with a diamond cup wheel working along a wall with a vacuum hose2

    Edges and details

    Edge grinders reach along walls, columns and corners so the whole floor matches.

  3. A worker in a respirator pushing a walk-behind grinder with a large dust extractor beside it3

    Dust control

    Machines run with shrouds and HEPA-grade extractors that capture the dust where it is made.

  4. A close-up of metal-bond diamond segments on a grinding disc against raw concrete4

    Diamond tooling

    Metal and resin diamonds work up through the grits, each step erasing the last one's scratches.

  5. A high-speed burnisher polishing a large mirror-gloss warehouse floor5

    Burnish and guard

    A high-speed burnisher works the guard in and brings up the final shine.

  6. A gloss meter resting on a mirror-polished concrete floor6

    Measure the gloss

    A gloss meter checks the finish, so you get a number and not just a look.

Where we work

Tampa is home base, and Florida is the territory

Pick an area and the map flies there, or tap a pin. Each one opens that city’s page.

What clients say

Straight from the floor

I was looking to have a 27 year old concrete floor in a massive distribution center cleaned and polished and all roads lead me to Tony, owner of Intelli-Clean. Intelli-Clean has the state of the art equipment to clean and polish any size concrete job. As I learned rather quickly, all concrete floors are not created equal. Tony's vast experience in dealing with all types of concrete proved invaluable in this project. The end result was a 27 year old floor that looked brand new with a shine that was truly amazing. My company refers to him as "The Floor Whisperer".

Johnny DavisOwner, Grease Police LLC

Great company. Tony does awesome work! We used him to mechanically harden our shop floor because we repair a lot of track equipment. He also helped to seal the floor so oil spills will not penetrate the concrete and can easily be cleaned. Highly recommend this company for all your flooring needs.

A shop ownerMechanically hardened and sealed shop floor
A gloss meter resting on a mirror-polished concrete floor
About Intelli-Clean

Since 1968, floors for businesses and the builders behind them.

Intelli-Clean Solutions, Inc. has served commercial clients and general contractors in Tampa and across Florida since 1968. Clients call Tony the Floor Whisperer. We look at the slab first, test before we promise, polish with real diamond tooling and leave the space clean, so you can see and trust the difference.

  • Honest about the slabWe tell you what we find, what a floor can and cannot become and what it will take in time and care, before you decide.
  • Samples before the floorA polished, dyed or coated test area on your own concrete shows the real result before the whole floor is done.
  • Planned around your businessYour hours, your deliveries and your customers shape the schedule, not the other way around.
  • Left cleanDust is captured, protection comes down and the space is handed back ready to use.

More about us

Questions

Before you call

What do you do?

We polish concrete floors and install epoxy flooring, polished overlays and concrete stains for warehouses, stores, restaurants, dealerships, clinics, offices and other commercial buildings in Tampa and across Florida, and for homes too.

What is the grinder at the top of the page?

It is a small hands-on demo. Drag the grinder across the raw floor and each pass turns it from dull to mirror. The numbers for gloss, area and machine time are typical figures. A real job starts with a walk across your slab.

Can you polish the concrete I already have?

Most sound slabs can be polished. We test hardness, moisture and condition, polish a small area so you can see it and tell you plainly what will still show, such as cracks or patches.

How long does a polish take?

It depends on the size, the starting condition and the finish. The Polish Planner on this site shows the steps and the hours, and a site visit turns that into a schedule.

Can you work while my business stays open?

Often yes. We split the building into zones, control the dust with shrouded machines and extractors and schedule the loudest steps for nights and weekends.

Polished concrete or epoxy?

Polish is the slab itself, hardened and shined, with almost no upkeep. Epoxy is a coating that adds color and chemical resistance. Many buildings use both in different zones.

Do you serve all of Florida?

Yes. Our home base is Tampa and we serve cities from Pensacola to Miami. Use the map on this site or call to confirm your city.

How do I get started?

Call or text, or send the form, and set up a visit. Tell us about the building and the floor you have now.

Ready for a floor that shines?

Call or text Intelli-Clean in Tampa, or send the form, and we will set up a visit. Tell us about the building and the floor you have now.

Visit

Let's get your floor shining.

Tell us about the building and the floor you have now. We read every message and reply with clear next steps and a time to walk the slab with you.

  • Your building: what it is used for, how big the floor is and what is on it now
  • Your city, the finish you have in mind, and any plan you saved from a tool on this site
  • A visit where we test the slab, polish a small patch and begin a plan around your hours
Prefer to talk? Call or text(813) 516-3422

Your estimate request

Prefer to type? Text your request. We only use your details to respond to your request.